LowRyter

thanks Phil. The rain came in today and cut my ride short. I'll just have to keep riding it until the oil remerges.

After a 10 miles ride it's all clear on the front of the engine. I'll just keep riding it. The talcum powder seems to do a nice job cleaning the engine.

I checked the sloppage plate when I dropped the pan. All of the fasteners were tight. Since it hasn't been touched since I purchased the bike 30k miles ago, I would be surprised if the upper gasket was leaking but OTOH, it's misting somewhere. BTW, are the oil lines supposed to be frozen to the point that I can't wrench them off? Yeah, I'll try talcum powder. thanks guys

perhaps it's the upper sump. i've got the slopage plate and I've never taken it off. I always take the front cover off to set the valves, wouldn't that be wet if it was the front seal or the timing set? Regarding the oil lines, I've never been able to get them to budge even when dropping the pan to change the filter. They're really solid.

Thanks Docc, You too Marty

'01 V11 Sport has been spraying quite a bit of oil from the front of the engine for the last few months. I recently serviced the bike and replaced the pan gasket but it didn't fix the problem. The oil lines seen solid, I can't even move the attaching nuts with a wrench. It doesn't drip, it only gets misty dirty when I ride it. I am hoping it's not another issue like the gearbox. At the same time, other than the aesthetics of it, it's no problem regarding oil consumption. So is there any consensus or BTDT? Appreciate your help. This 100 miles or so.

350 miles of dirt? That's manly.

Interesting Tim. I'm aware of Strategic and Tactical leaders but I hadn't thought about Networking leadership. Intuitively, it's quite obvious but I've not seen it articulated before.

I remember seeing the crash on the news when I was a kid. I also remember seeing Breedlove's Sonic 1 displayed at one of the local Goodyear stores.

I'd consider getting a red frame transmission brace so long as you are replacing the tranny.

I want to pass on that Don Moomaw at Motiv Cycleworks is moving his shop to 906 N. Ann Arbor Ave, Oklahoma City, OK and will open a new franchise for Moto Guzzi, Aprilia and Vespa. Ann Arbor is midway between Macarthur and Meridian.

GMC28 My Suzuki Bandit eats clutches. Using Rotella was the death knell for clutch #2. I've never used it since in anything but my Duramax. Funny, I used it in the Bandit because I read the positives on Max Suzuki board. Then I read -never to use it- on the same board but it was too late. Looking back, I am not certain Rotella killed that clutch but I don't walk under that ladder again.

There's a little bit of trick with that API chart. Many of the new weights are only available in SL and/or Fully Synth. Now if you run a Model A Ford that uses straight 20 WT, you won't find an SL oil. You might not even find straight 20 at all and will have to go with 10w30 which you can probably get in SL grade full synth. I know I got a coupon for a cheap oil change on my '14 Accord from the dealer. I went over there and they said they couldn't honor the coupon because the coupon was for conventional oil. I said fine, I'll take conventional. Well they don't make conventional oil in the weight (0w-20) that goes in my car, despite the weasel words in the owner's manual (probably written by lawyers ). I did check and you can get 20W50 in SL grade.

According to the link: SL Current For 2004 and older automotive engines. I am no lawyer but I don't have an automotive engine in my motorcycle According to the web site for Actevo: Features: Outstanding high temperature oil consumption and oxidation control Exceeds API SG, JASO MA2 In the long run, does it matter? who cares? Run what ya want. Maybe it's a marketing gimmick for motorcycle geeks? I would be pretty square not to use it on my wet clutch Suzuki. That's a definite no-no. Or better yet, Suzuki convetional oil which used to be $18/gallon, now $40. Yep, that obsolete SG oil will probably cost more than the new SL stuff. .

No. SL does NOT meet SG standards. SL is made for newer cars for good gas mileage. SG is made for heavy use for motorcycles (and older vehicles). Different specs, different mineral additives. Agree that it is important for wet clutches but also has advantages for air cooled engines with solid lifters. For a Spine Frame, I would use 20-50 SG Motorcycle oil. There's a complete thread on it. I like the Castrol Motorcycle Synth Blend.

Dave, I don't think the consensus is that SL is acceptable and to continue to use SG.

That's OK. I found a couple of inches of broken hose clamp in the bottom my sump. why worry about paper?

You might want a bigger ratchet to get the filter on tight. (I use my hands) (I drop the pan too. I tried the manhole and could never get it threaded back on when the bike was on the side stand.)

Don is moving his shop to a new location. Should be a Moto Guzzi dealer with bikes in March. I expect that he'll have a a couple of dozen bikes and scooters. He will keep the same name, Motiv Cycleworks

Very nice looking bike, Blight.

My goodness, I wondered how far this was going to go. Man, it's went. Docc, How many lost horsepowers do you think has escaped from your 100k mile motor's rockers? I was thinking that compression tests after every fill up will complete a heck of a graph.

drummers are folks that like to hang around musicians.