Zooter Posted February 13, 2015 Share Posted February 13, 2015 The factory stand is well and good. I don't have one and probably half of you don't either, so what are you using? It's not clear in any photo I've seen, where the stand latches on. I guess under the rear subframe just inside the bottom of the porkchops? I have a cunning plan ( I could be related to Baldrick too ), but before I embarrass myself and drop it, what works to get the rear off the ground and level? Link to comment Share on other sites More sharing options...
fotoguzzi Posted February 13, 2015 Share Posted February 13, 2015 2 Link to comment Share on other sites More sharing options...
docc Posted February 13, 2015 Share Posted February 13, 2015 The factory stand captures the two nuts on the very bottom attachment of the porkchops that through-bolts under the back of the gearbox. Link to comment Share on other sites More sharing options...
Craig Posted February 13, 2015 Share Posted February 13, 2015 I like my factory stand. It pays for itself very quickly. Link to comment Share on other sites More sharing options...
Zooter Posted February 13, 2015 Author Share Posted February 13, 2015 I like my factory stand. It pays for itself very quickly.A volunteer! Please measure the height of the lower porkchop bolt off the floor when stand up. Also, how high is the rear tyre off the ground? Link to comment Share on other sites More sharing options...
Gottagetone Posted February 13, 2015 Share Posted February 13, 2015 I just picked up a swing arm stand at Harbor Freight, with the 20% off coupon it was $25. I did have to "manipulate" the stand a bit to fit the swing arm but it works just fine. Link to comment Share on other sites More sharing options...
docc Posted February 13, 2015 Share Posted February 13, 2015 I like my factory stand. It pays for itself very quickly.A volunteer! Please measure the height of the lower porkchop bolt off the floor when stand up. Also, how high is the rear tyre off the ground? With the preload cranked up on my Ohlins, I have to put a 4x4 block under the factory stand handle to get the rear tire to clear the floor about an inch. 1 Link to comment Share on other sites More sharing options...
Zooter Posted February 13, 2015 Author Share Posted February 13, 2015 I might be lucky to buy a pair of suitable wheels for $25 here. My cunning plan involves scraps of timber, minimally high enough to get the rear wheel in the air in the resting position. Link to comment Share on other sites More sharing options...
Zooter Posted February 13, 2015 Author Share Posted February 13, 2015 I like my factory stand. It pays for itself very quickly. A volunteer! Please measure the height of the lower porkchop bolt off the floor when stand up. Also, how high is the rear tyre off the ground? With the preload cranked up on my Ohlins, I have to put a 4x4 block under the factory stand handle to get the rear tire to clear the floor about an inch.Thanks, I hadn't forgotten about variations in suspensions, sitting on the ground, how high is your porkchop bolt? Link to comment Share on other sites More sharing options...
docc Posted February 14, 2015 Share Posted February 14, 2015 The nuts are off the deck about 10 1/2 inches with the front up about an inch in the Sport Chock. Link to comment Share on other sites More sharing options...
Zooter Posted February 14, 2015 Author Share Posted February 14, 2015 And how high the nuts with the stand propped on 4x2? Link to comment Share on other sites More sharing options...
LowRyter Posted February 14, 2015 Share Posted February 14, 2015 I just picked up a swing arm stand at Harbor Freight, with the 20% off coupon it was $25. I did have to "manipulate" the stand a bit to fit the swing arm but it works just fine. Link to comment Share on other sites More sharing options...
Craig Posted February 14, 2015 Share Posted February 14, 2015 I like my factory stand. It pays for itself very quickly.A volunteer! Please measure the height of the lower porkchop bolt off the floor when stand up. Also, how high is the rear tyre off the ground? 11" (30cm) from floor to center of bolt. 1.75-2 (4.4-5cm) inches below the rear tire. Link to comment Share on other sites More sharing options...
Zooter Posted February 14, 2015 Author Share Posted February 14, 2015 Rough Maths ( Stand Height @ porkchop - porkchop height - front chock lift ) /=/ ( rear droop + rear wheel clearance) Assumes stand is roughly in the middle. Link to comment Share on other sites More sharing options...
Zooter Posted February 14, 2015 Author Share Posted February 14, 2015 I like my factory stand. It pays for itself very quickly.A volunteer! Please measure the height of the lower porkchop bolt off the floor when stand up. Also, how high is the rear tyre off the ground? 11" (30cm) from floor to center of bolt. 1.75-2 (4.4-5cm) inches below the rear tire.Thanks, I'll assume you have stock suspension. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now