windchill Posted June 26, 2006 Posted June 26, 2006 I am now the proud owner of a shiny black belly pan supplied by Motomecca: stunnigly well made it is too. However, if I have to remove the sump screws to fix, I need to know what to re-torque them to - anyone know?
Paul Minnaert Posted June 26, 2006 Posted June 26, 2006 hand tight is best, be very carefull it you realy want to do this with a torque wrench. Its a nasty place to get broken bolts out. Don't ask me how I know.
Baldini Posted June 26, 2006 Posted June 26, 2006 ...but at the same time - don't do em to loose or your arse'll fall off
windchill Posted June 26, 2006 Author Posted June 26, 2006 I actually invested in a small torque wrench a few years ago that goes down to 5Nm! So hand tight and loctite? Thanks for the advice
Guest Rocker Posted June 27, 2006 Posted June 27, 2006 I am now the proud owner of a shiny black belly pan supplied by Motomecca: stunnigly well made it is too. However, if I have to remove the sump screws to fix, I need to know what to re-torque them to - anyone know? 93367[/snapback] Use: 1. Common sense. 2. Check leverage of remainig secure bolts when securing. 3. Don't use huge leverage when tightening. P.S. Check the smaller "side bolts" on the belly pan after 1000km - if loose replace them with loctite. P.P.S NEVER loctite sump bolts! Rockerob.
windchill Posted July 5, 2006 Author Posted July 5, 2006 Anyone who has fitted one of these: how tight did you find it at the front end of the engine? Mine wouldn't fit without serious surgery to reduce the overall width at the very front end of the mounting brackets. I needed to "gain" almost 3/16" to get it to slide on far enough for the holes in the pan to mate with those on the brackets. Also there is a "block" or "blank" on the bottom of the crank case casting at the front on the RHS (viewed from onboard) against which my pan is tight up.
windchill Posted July 5, 2006 Author Posted July 5, 2006 BTW, using my "lightweight" torquewrench and a degree of very elusive synwir cyffredin, I found that the sump screws were allready set to 8Nm: the bottom end of the suggested 8 - 12 Nm range. Didn't use nut lock on them, I reckoned weld seal would be better given the levels of vibration present (sais gwirion)
windchill Posted July 16, 2006 Author Posted July 16, 2006 A dyma ni gyfeillion!! Job done!! Just thought you might like to see it on, weldseal and all!! Why can't I post pics any more?
windchill Posted July 16, 2006 Author Posted July 16, 2006 Hmmm!! I've done the usual: "Browse" found the pic, then pressed "Add this attachement", but nothing seems to happen!!
Paul Minnaert Posted July 16, 2006 Posted July 16, 2006 maybe you have a to big picture or all your attachment space is used. You can check this at "my controls" on to of the page. I just looked, you have uploaded a bunch 900kb pictures, in two threads. Normaly pictures should not be bigger than 100kb, and can be big enough to view. Resize the pictures first before uploading.
windchill Posted July 16, 2006 Author Posted July 16, 2006 Nope, I've got the usual 9.94 megs!! My pics are way smaller!! NEVER been asked to make anything smaller before : usually the opposite! Looks lie you is correct sir!! Whilst the script says that the global limit is 9.94mb, the arror mesage syas the pics are too big, even at 602kb each!! Last time, I just added and posted!!! Has my Goldmember subscription lapsed perhaps? Reduced the size to used 9.59 of 19+mb!! so should be plenty? maybe you have a to big picture or all your attachment space is used. You can check this at "my controls" on to of the page. I just looked, you have uploaded a bunch 900kb pictures, in two threads. Normaly pictures should not be bigger than 100kb, and can be big enough to view. Resize the pictures first before uploading. Give up!! Good night chapos!
Paul Minnaert Posted July 16, 2006 Posted July 16, 2006 I just looked at all attachments that are there at the moment: there are 6000. From that 6000 are 17 that are bigger than 200kb. You are correct about the 20mb max on your account, but there is a max of 200kb per post. That has been larger, then from time to time Jaap or me had to download all big pictures, resize them and upload again. Otherwise available webspace would have ended a long time ago. I sugest you resize the pictres to 1024x768max size before uploading. You don't have to buy anything for that, if you have XP, you can download a image resizer tool from the Microsoft site. Other tools like infranview can do that too, that's freeware. To try I let xp resize your biggest picture, that was 900 kb, now 166kb
windchill Posted July 17, 2006 Author Posted July 17, 2006 Still throws up error message at 1024x768! HELP
Alex-Corsa Posted July 19, 2006 Posted July 19, 2006 Still throws up error message at 1024x768! HELP Perhaps go to http://www.imageshack.us/ and host it for free, it''s so easy
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now